Set up a Yealink cordless phone
Set up Yealink cordless phones in one of two ways: on a W60B base station that plugs into your network, or with a DD10K adapter that turns a Yealink desk phone into the base. This article is for the administrator or IT person who installs the phones. Cordless phones reach their base over DECT, the radio standard for cordless phones, which is why some menus say DECT.
Before you start
| W60B base station | DD10K adapter | |
|---|---|---|
| Where it connects | Your network, by cable | The USB port of a T53, T53W, T54W or T57W desk phone |
| Cordless phones it takes | Up to 8 | Up to 4, in addition to the desk phone |
Registering a cordless phone can ask for the base PIN. It is 0000 unless someone changed it.
Set up a base station and its first cordless phone
The box of the base holds the base, its stand, a power adapter and a network cable.

- Plug the network cable into the base and into your network switch or wall jack. If your network doesn’t supply Power over Ethernet (PoE, power through the network cable), also plug in the power adapter that came with the base.
- Snap the stand onto the back of the base, with the cables running through it.

- Put the battery in the cordless phone, plug in its charger cradle and set the phone on the cradle. The phone turns on by itself.
- On the base, press and hold the round button on the front until the top light flashes slowly.

- On the cordless phone, press the Reg soft key (the soft keys are the two keys under its screen). The screen shows Easy Pairing, then Handset Subscribed when the phone is registered.
Register by hand when Easy Pairing doesn’t start
- While the top light of the base is flashing, press OK on the cordless phone to open its menu, then go to Settings > Registration > Register Handset.
- Select the base and press the OK soft key. The phone searches for the base.
- When the phone finds the base, press the OK soft key.
- Enter the base PIN and press the Done soft key. The screen shows Handset Subscribed.
Add another cordless phone to a base station
A W60B base takes up to 8 cordless phones. For each new one:
- Put the battery in the new cordless phone and set the phone on its charger cradle.
- On the base, press and hold the round button until the top light flashes slowly.
- On the new cordless phone, press the Reg soft key and wait for Handset Subscribed.
Set up cordless phones with a DD10K adapter
The DD10K plugs into a T53, T53W, T54W or T57W desk phone and makes it the base. The desk phone itself counts as Handset 1, so the first cordless phone is Handset 2.
Important: The first time the DD10K is plugged in, the desk phone may update it, which can take 15 minutes or more. Don’t unplug the desk phone or pull out the DD10K during the update.
- Plug the DD10K into the USB port on the back of the desk phone, behind the screen. If an update starts, wait for it to finish: the screen then shows Connect DECT dongle successfully! for a few seconds.



- On the desk phone, press the Menu soft key and open DECT Settings. On a T53 or T53W, open Menu > Settings > DECT Settings.

- Open Handsets.

- Highlight the first slot marked Unregistered, starting with Handset 2, and press the Start Reg soft key. On a T57W, tap Register. The slot shows Registering.


- On the cordless phone, press the Reg soft key. The screen shows Easy Pairing, then Handset Subscribed.



- On the desk phone, check that the slot now shows Registered. Repeat steps 4 and 5 for each cordless phone, up to 4.

Choose which extension rings on each cordless phone
Which extension rings on which phone is set on our side. With a DD10K, the desk phone starts out with all of your lines, and you will likely want some of them on the desk phone and the others on the cordless phones. Contact support with the extension you want on each phone, and we will set it.
The cordless phone doesn’t find the base
- Check that the base has power: its lights are on.
- The base accepts a new phone only while its top light is flashing. Hold the round button again until the light flashes slowly, then press Reg on the cordless phone.
- Bring the cordless phone close to the base and try again.
The desk phone doesn’t show DECT Settings
The DD10K works only in a T53, T53W, T54W or T57W: another model never shows DECT Settings. On one of these models, unplug the DD10K, plug it back in firmly and wait for the update to finish.